Effects of hydrolysis of precursor on the structures and properties of polymer-derived SiBN ceramic fibers

In this paper, polyborosilazane precursor was synthesied from HMDZ, HSiCl₃, BCl₃ and CH₃NH₂ using a multistep method. By controlling the storage conditions, parts of the polyborosilazane fibers were hydrolyzed. FT-IR, NMR, XRD, TEM and monofilament tensile strength test were employed to study the effects of hydrolysis of precursor on the structures and properties of polymer-derived SiBN ceramic fibers. FT-IR and NMR results indicate that Si-N group in PBSZ reacts with H₂O to form Si-O-Si group. After pyrolysis reaction at 1400℃, Si-O-Si group will finally transformed into highly ordered cristobalite and β-quartz, resulting in formation of the wrinkled surface of the obtained SiBN ceramic fiber. The strip-like defects on fiber surface, according to monofilament tensile strength test, had a significant effect on mechanical property of the obtained SiBN ceramic fiber and caused no increase in fiber tensile strength of hydrolytic polyborosilazane fiber before and after pyrolytic process.     

机加工孔套管抗挤压强度有限元分析

套管屈服强度直接影响套管抗挤压性能，套管在加工孔过程中可能诱发孔眼附近材料发生金属相变，导致套管屈服强度不再均匀分布，进而影响套管抗挤压强度。在相同工况下，对比了P110完整套管和机加工孔套管的抗挤压强度，以此为参照组分析了相变区域面积和相变区域屈服强度对机加工孔套管抗挤压强度的影响。结果表明，机加工孔会改变材料屈服强度，进而影响套管抗挤压性能。随金属相变区域屈服强度减小，机加工孔套管抗挤压强度减弱；当金属相变区域屈服强度增大时，机加工孔套管抗挤压强度增强。且机加工孔套管相变区域面积对机加工孔套管抗挤压强度的影响随相变区域屈服强度增加而逐渐削弱。     

DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

Polymer hydrogel cross-linked by inorganic nanoparticles for removing trace metal ions

Hydrogels for absorbing metal ions in wastewater have attracted more attentions in the environmental field especially for recent years. The removal efficiency of hydrogel adsorbents for eliminating metal ions is highly related with the effective contact between adsorbents and adsorbates. However, poor water absorption capacity of the hydrogel adsorbents would restrict on the expose of adsorption sites to the targeted subjects, causing undesirable removal ratio (RR) especially for metal ions at trace level. Thereby, the reported hydrogel adsorbents mainly focus on the removal of high content but not the trace level of metal ions so far. In this work, poly(acrylamide) (PAM)/poly(acrylic acid) (PAA)/Ca(OH)₂ composite hydrogel is applied to adsorb trace metal ions. Swelling ratio of such PAM/PAA/Ca(OH)₂ gel reaches 2,530 g/g, resulting in effective exposure of active sites and further expected RR for trace metal ions. The RRs of such adsorbent for Cu²⁺ (initial concentration C₀ = 0.064 mg/L), Al³⁺ (C₀ = 0.27 mg/L), Co²⁺ (C₀ = 0.59 mg/L), Cr⁶⁺ (C₀ = 0.52 mg/L), Mn²⁺ (C₀ = 0.55 mg/L), Ni²⁺ (C₀ = 0.59 mg/L), Zn²⁺ (C₀ = 0.65 mg/L), Ag⁺ (C₀ = 1.08 mg/L), and La³⁺ (C₀ = 1.39 mg/L) are 56.6, 80.8, 41.3, 29.3, 34.6, 44.6, 55.9, 45.8, and 35.5%, respectively. This work broadens the application of hydrogel adsorbent for eliminating trace metal ions from polluted water.     

Effect of ultrasonic vibration on thermal and material flow behavior,microstructure and mechanical properties of friction stir welded Al/Cu joints

Al/Cu dissimilar joint has been widely produced by using friction stir welding (FSW), but the weld quality remains limited. A recently developed ultrasonic     

萃取塔数学模型及过程强化的若干研究进展

萃取塔因生产能力大、占地面积小、密闭性好等优点，在石油、化工、生物、医药和环境工程等多领域被广泛应用。本文从以下几个方面介绍了萃取塔近些年的研究进展：综述了传统萃取塔（脉冲萃取塔、转盘塔与Kühni塔等）的水力学、轴向扩散与传质模型的发展，分析比较了表面张力、传质方向、放大效应等因素对模型的影响；介绍了计算流体动力学（CFD）在萃取塔中单液滴、单相流模拟、液-液两相流模拟、外加能量模拟、与群体平衡模型（PBM）耦合模拟中的应用进展；介绍了国内外设计开发的新型萃取塔，包括改变传统塔的内构件和引入多种外场能量等方式来强化相间传质。研究表明，将先进实验研究方法、准确经验模型和可靠理论计算相结合，将会是萃取塔研究的重要手段和方向。